Customer #416527 on DEV-11013 - LilyPad MP3
I watched te product demo. Is all you need to make this wearable the Lilypad MP3, a microsd card that I can load music on from my mac, the rotary encoder and a couple of thin speakers, and thread to...
View ArticleOldFar-SeeingArt on DEV-09476 - WIZnet Serial-to-Ethernet Gateway - WIZ110SR
It just took me a few hours to get this working so here are some tips for others… most of it can be found in other comments here but this is what I learned: a) the serial port is identical to a pc –...
View ArticleCustomer #414764 on ROB-09238 - Stepper Motor with Cable
I AM TRYING TO CONTROL CURTAINS AT HOME USING THE ARDUINO + MOTOR SHIELD I HAVE THIS STEPPER MOTOR RS 5350372, BUT I AM NOT SURE IF THIS IS ENOUGH TO DRIVE THE CURTAIN. WHAT ABOUT USING ONE OF YOUR 12V...
View ArticleKamiquasi on Nat'l Teacher Appreciation Week and Interview with Travis O'Hair
Yeah, things did get derailed a bit – but, man, what’s your problem with pandas!? :PI thought it was an interesting interview and figured I’d check what would be similar programs in NL. Turns out,...
View Articlered913 on COM-08589 - Diode Rectifier - 1A 50V
Anybody know what the voltage drop across this might be? About .7v?
View ArticleNavig8or on GPS-09838 - 20 Channel LS20126 GPS Receiver
the output is already at TTL levels. your problem might be with the baud rate.
View ArticleCustomer #384437 on GPS-11058 - Venus GPS with SMA Connector
Hello, I have one of these about 6 months old. I am using the example tutorial from Simon Monk above. My GPS gets a fix, and the red lights flashes.My issue is that it seems as though I do not get...
View ArticleCustomer #436311 on WRL-08687 - XBee Explorer USB
Use the board all the time but I am wondering how I can use it just for talking to the Arduino with serial. I have tried to put the Dout and Din on to the Arduinos Tx0 and Rx0 ports and it doesn’t...
View ArticleCustomer #220425 on Flexiforce Pressure Sensor (25lbs) Quick Start Guide
if you are trying to have multiple pressure sensor to a single board, what would you do in wiring?
View ArticleCustomer #436336 on ROB-10551 - Small Stepper Motor
which colored wires of the stepper motor go in to what location of the EasyDriver Stepper Motor Driver? little confused
View ArticleCustomer #69070 on WRL-11600 - RN41-XV Bluetooth Module - Chip Antenna
Does not work with FIO V3 if you just plug it in. the CTS / RTS pins are swapped and there is not breakout for the CTS pin 16 on the FIO V3. What I did to get this to work is added a jumper on th RN-42...
View ArticleCustomer #69070 on WRL-10822 - RN-XV WiFly Module - Wire Antenna
I could not get adhoc to work from by android phone, gave up and used access point
View ArticleCustomer #391181 on SEN-09569 - Humidity Sensor - HIH-4030 Breakout
I have a problem with the output – when supply voltage is 5V, sensor gives about 3V – according to datasheet this refers to about 70%RH but … my office already has RH meter (air conditioning, office...
View ArticleCustomer #413822 on WRL-09976 - XBee Shield
Could Sparkfun us forum style software, because all this information is essential to using the product, but this comment thread is unorganised and unsearchable.
View Articlecmat on Engineer Thursday - An Introduction to Ino Toolkit
Thanks, I’ve been looking to automate things. I use MATLAB/Octave and Python to program experiments and communicate with external devices, would be great to write and compile everything in one IDE.
View ArticleRyeMAC3 on Engineer Thursday - An Introduction to Ino Toolkit
OK, just trying to understand why someone would see “not recompiling” as a perk. Even my iOS projects that use hundreds and hundreds of sources files and are a good 60M only take about 20 seconds (if...
View Articlebrennen on Engineer Thursday - An Introduction to Ino Toolkit
Awesome. This is pretty much exactly what I’ve wanted since I first cracked open the Arduino IDE. I mean, it’s a fine little shim for the things it bundles up, but it’s kind of a ball of sadness as...
View Article