RalfieRoo on SEN-09587 - ePIR
Anyone have any recommendations for permanent mounting of these? I'm trying to get them to face away from the circuit board, but since they are mounted on 90 degree headers I can't seem to get it quite...
View ArticleCustomer #194186 on Hygrometers: A Cautionary Tale
Do you still use humidification packs in it, or some other means of controlling humidity?
View ArticleKinch on Hygrometers: A Cautionary Tale
It actually has a container at the bottom of humidity beads that we periodically refresh with water. The controller box monitors the humidity level and if the RH gets too low it turns on the fans you...
View ArticleCustomer #333257 on Hygrometers: A Cautionary Tale
As of this writing, your product description page does not have any mention of "re-hydration" or a link to this important information for the use of this sensor. Might someone remedy this omission?
View ArticleTimZaman on COM-11152 - Audio Jack - 1/4" Stereo (vertical)
This is actually delivered with a flimsy silver ring instead of the nice dark plastic screw that belongs to it.
View ArticleDellaa87 on WRL-08664 - XBee 1mW Chip Antenna - Series 1 (802.15.4)
Can you trim the pins of the XBees without causing it harm?
View ArticleToni_K on WRL-09145 - Interface Cable SMA to U.FL
If this is the Wifly shield you have, then yes, this is the correct cable to connect the module to an external antenna that has an SMA connector on it. The RP-SMA interface cable would also work, but...
View ArticleLightManCA on Hygrometers: A Cautionary Tale
So...You were selling partially hydrogenated sensors? Clogging my arteries! (Sorry I couldn't resist. Really you guys are awesome. I bet many manufacturers wouldn't notice that kind of thing and go to...
View ArticleKinch on Hygrometers: A Cautionary Tale
I can see that being beneficial should anyone need to re-calibrate their board at any point. We'll try and get something thrown up on each product sometime soon. As of right now that information is...
View ArticleJoeisi on Hygrometers: A Cautionary Tale
When I first started reading this, all I could think about is Fight Club:"Take the number of vehicles in the field, A, and multiply it by the probable rate of failure, B, then multiply the result by...
View ArticleCustomer #374389 on WRL-10534 - RF Link Transmitter - 434MHz
I would like to know a solution to the issue i am facing. If, let's say, I need to supply this transmitter module (434MHz) a higher voltage (e.g. 9V) in order to increase the transmission range or...
View ArticleCustomer #99858 on ROB-09347 - Servo - Large Full Rotation
Could someone explain what the "Rest point adjustment" does. Thank you.
View Articleliseman on DEV-11401 - Electric Imp Shield
I've got some sample code (and design for my own imp + arduino on one board) here. they're for sale, if you're interested.
View ArticleKevin_S on SEN-10988 - TMP36 - Temperature Sensor
Need HELP!!! Please!!! I am using a TMP36 sensor in my truck with an embedded Atmega328 chip and lcd display. Everything worked fine when I breadboard the circuit with an Arduino Uno. Once I made a...
View ArticleCustomer #418704 on PRT-11496 - Solar Charger and Battery Pack - 3500mAh
may i have a specification sheet for the solar circuit functions in details please ?
View ArticleCustomer #386203 on TOL-10951 - Polymorph - 1000g
No, avg pla melts at 185c.Source: I own 3 3d printers.
View ArticleCustomer #418727 on PRT-11667 - TuxCase - Arduino Enclosure
Any chance of a Mega version?
View ArticleMitch.Tolson on LAB-11480 - Hack Pack Workshop Supply Kit
Well, there's this... pretty close: https://www.sparkfun.com/products/10874
View Article