simmers on BOB-08849 - Breakout Board for VS1000D
Is there any difference between your firmware and usbspk.c from here: http://www.vlsi.fi/fileadmin/software/VS1000/usbspk.c?I recently flashed my breakout with this firmware, and its behaviour is quite...
View ArticleCustomer #445267 on SEN-00242 - Infrared Proximity Sensor - Sharp GP2Y0A21YK
This is one of the best infrared sensor. simple and with a friendly interface the sharp sensor has high accuracy for its price. many more infrared sensors could be found here...
View ArticleScaredyCat on WRL-11395 - Electric Imp
I keep coming back to the EI, get really excited about it right up to the point where I remember it relies on some cloud service for development and transmitting data. Essentially a useless product...
View ArticleCustomer #331581 on SEN-10061 - LinkSprite JPEG Color Camera TTL Interface
Sorry I did not see your post before. TBH I dont remember what I changed exactly but it boiled down to some delay that had to be suppessed or added. This thing is pretty sensitive to how you handle the...
View ArticleCustomer #425531 on PRT-11362 - SD/MMC Socket for Secure Digital Disk or...
is this the slide in or click in?
View ArticleClik here to view.
TheCentaur on TOL-11763 - S.H.O.V.E.L.
Good use for my S.H.O.V.E.L. – Opening SparkFun parts polybags…
View ArticleAndy on DEV-11168 - AVR ISP Shield - PTH Kit
So I am able to burn the bootloader via Arduino IDE (1.0.5) using my duemilanove as the ISP. When I try to then upload a sketch to the chip while in the sheild (using “Upload using programmer”), it...
View ArticleJeff on Beatty Robotics builds Mars Rover, blows our minds
Very nice work, very neat and professional, innovative! My ten year old is becoming interested in programming my stamp and Arduino creations, I can only hope he reaches a fraction of your level, Nice...
View ArticleRobertC. on BOB-08849 - Breakout Board for VS1000D
Honestly, I couldn’t tell you. It is most likely the same though.
View ArticlePalmTreesandPICs on DEV-11649 - Danger Shield
This one is WAY More Dangerous.Previous Danger Level: steven seagalCurrent Danger Level: jean claude van damme (whilst doing a split)
View ArticleLaserJockey on Engineer Thursday - Bring on the Lasers!
Just remember the two rules of laser safety – don’t look into the laser beam, and don’t chew on the power supplies. Laser accidents happen at the speed of light, you know.I think I see my old lab...
View ArticleRobertC. on SEN-11836 - Fingerprint Scanner - 5V TTL (GT-511C1)
oops, price didn’t carry over, thanks! fixed now.
View ArticleShloimy on DEV-10327 - PodSocket Breakout
Cool. Now all we need is a breakout for the new lightning charger
View ArticleCustomer #448296 on MaKey MaKey QuickStart Guide
I have the Makey Makey by Joylabz and the driver won’t install for me. Will this only work for Makey Makeys made by SparkFun?
View ArticleTeslaFan on PRT-11830 - TuxCase - Raspberry Pi Enclosure
The only way for this product to be more over the top is to make it in 6 different anodized finishes. That way you can not only buy an over engineered case for your Pi, but you can collect all the...
View ArticleCustomer #448298 on KIT-09612 - Audio Amplifier Kit - STA540
A spike on the 12V rail is more like 13.8V, not 100V. During cranking the voltage drops to about 9V.
View ArticleChris on KIT-09612 - Audio Amplifier Kit - STA540
Hey Troy. I’m using the same setup as you and yes, you can just connect the ground wire to one or both of the negative terminals. The negatives are connected on the board. Works great for me! Good luck...
View Article