Customer #406195 on SEN-11486 - 9 Degrees of Freedom - MPU-9150 Breakout
Could someone tell me how to make vibration noise reduction filter for this IMU, and how can i get the more accurate data possible
View ArticleCustomer #405386 on SEN-11486 - 9 Degrees of Freedom - MPU-9150 Breakout
I managed to make the example code work on Arduino duo board. However, there is drifting in Quaternion readings. Anybody got this problem?
View ArticleThimplum on ROB-11057 - Wild Thumper Controller Board
Can anyone help me with how to wire this with a 6 channel RC receiver? I’m a bit lost.
View ArticleCustomer #114781 on COM-11759 - Infrared Remote Control
Does the circuit board allow for up to 18 buttons? Are each of the pads unique?
View ArticleToni_K on LCD-09395 - Serial Enabled 16x2 LCD - White on Black 5V
We recommend using this JST Interface cable.
View ArticleToni_K on DEV-09476 - WIZnet Serial-to-Ethernet Gateway - WIZ110SR
If you have questions about purchasing any items, please contact customerservice@sparkfun.com. They’ll be able to help you out!
View ArticleToni_K on SEN-10537 - Serial Accelerometer Dongle
Double check your connections are all good and power is appropriate. The data you are getting out may be due to a baud rate mismatch. I would double check that, and if you are still having issues after...
View Articlelaptopman on New Product Friday: Control Your Enthusiasm
I’m still excited for the RN-52 breakout!
View ArticleCustomer #451999 on BOB-10859 - L6470 Stepper Driver Breakout
yeah, “pB” i think is short version of pushbutton
View ArticleTECH-GEEK on New Product Friday: Control Your Enthusiasm
SparkFun likes the color Red too much
View ArticleLefty4000 on New Product Friday: Control Your Enthusiasm
Holy crap, the new ending song works so well!
View ArticleDC177E on New Product Friday: Control Your Enthusiasm
It’s just a throwback from their Viking heritage: a reminder of the good days pillaging.
View ArticleLuauLarry on KIT-11227 - SparkFun Inventor's Kit for Arduino
Any chance of getting notified when there’s a new version of the kit that accounts for some of John’s feedback? In particular, a kit with a white breadboard instead would be nice. I’m a COMPLETE...
View ArticleCustomer #10429 on DEV-09346 - MegaShield Kit for Arduino
None of the IO pins are connected to pads at the interior of the board. This makes soldering it more tedious and improvised than it would need to be. The 5v and GND bus are useful, but they would be...
View Articleautomaton on PRT-10968 - NCP1402-5V Step-Up Breakout
The schematic for this and the 3.3V version are identical. What actually differentiates the output voltage? I have the 5V version and was wondering what I’d have to change on it to get it to output 3.3V?
View ArticleKamiquasi on PRT-10968 - NCP1402-5V Step-Up Breakout
Unfortunately, you would have to replace the NCP1402 itself. It’s not a configurable device – ONSemi produces them in fixed output voltages; NCP1402: 200 mA PFM Micropower Boost ConverterIf you wanted...
View ArticleOldFar-SeeingArt on New Product Friday: Control Your Enthusiasm
What @Lefty4000 said… I like it also. Name of music?
View Articlegabe on ROB-11699 - Big Easy Driver
Glad I could help point you in the right direction for the second one. Good luck figuring out the other one!
View ArticlePharoahsMummy on PRT-11231 - Power Cell - LiPo Charger/Booster
I am having a problem with this unit. When a battery is connected, no load is present AND the charge cable is disconnected, the battery is run down to almost 0v. This is terrible for (unprotected)...
View ArticleME heat o nator on New Product Friday: Control Your Enthusiasm
I love that bare-bones SIK! Talk about a gateway drug for the young and impressionable.
View Article