Customer #424479 on COM-10878 - EL Escudo Dos
hi everyone is there any possibility to build up a system that provides 16 ports with one arduino board? and without a forfeit? ;) greetings from switzerland
View ArticleRyeMAC3 on PRT-09429 - 6 Pin Right Angle Female Header
An extra .45 cents because the pins are bent? Is there anything reason why you couldn’t order the .50 cent straight pin version and bend the pins?
View ArticleCustomer #424639 on SEN-11651 - Fingerprint Scanner - 5V TTL
Guys where is the Vcc, ground , tx & Rx
View ArticleCustomer #308911 on DEV-11055 - DIYDrones ArduIMU+ V3
I am going to use this to create a tracking system for my telescope. Does anyone have any advice on putting this in some kind of protective case? It doesn’t have anywhere to screw it down so could I...
View ArticleMikeGrusin on SEN-11651 - Fingerprint Scanner - 5V TTL
In the datasheet, in the mechanical drawing on the last page. Pin 1 is marked by a white triangle on the PCB.
View ArticleGeoffT on DEV-11780 - Teensy 3.0
Description says “You can program the Teensy in your favorite IDE using C…”. Has this been verified, and if so, on what non-Arduino IDE?
View Articlejpwsutton on COM-10407 - Rotary Encoder LED Ring Breakout Board - Blue
In the demo video it is shown that you can mount the rotary encoder through the board from the back. This would be preferable for my project as I would like to have the LEDs as close the the enclosure...
View ArticleCustomer #341499 on SEN-11651 - Fingerprint Scanner - 5V TTL
Any idea when this will be back in stock?
View ArticleMikeGrusin on COM-10407 - Rotary Encoder LED Ring Breakout Board - Blue
On our encoders, it looks like you could bend the legs 180 degrees and mount it from the back, but personally I’d be wary of this since you could easily snap a leg off. The safest thing might be to not...
View Articlepullinsb on COM-10438 - Thermal Printer
it’s too bad that this is on back order. i just had the idea to use a printer (this one) to print out a physical log of attached network clients, as they attach.using dd-wrt and an available serial...
View Articlerubot on Making Your Own Solder Paste Stencils
i was thinking of doing the same. did this work for you?
View ArticleTheRegnirps on According to Pete - The Time Cube
It is too bad some of the tricks of the trade get dropped from the engineering curriculum. The classic time travel shortcut is through the chronosynclastic infundibulum and everyone used to know how to...
View ArticleHoobert on According to Pete - The Time Cube
You got it wrong you have to be going 22MPH FASTER THAN TIME while using the Arduino to divide the target time travel speed(s/s) by zero. (negative numbers for reverse time travel) Otherwise you will...
View ArticleTheInventor on COM-10878 - EL Escudo Dos
Sorry, I never actually ended up completing my project as it proved too costly. I’d recommend googling around, there are a lot of good sources on the internet. Good luck!
View ArticleCustomer #382889 on PRT-11496 - Solar Charger and Battery Pack - 3500mAh
I just tried to use this as an arduino power source, intended for use in remote location project and it only stays on for about one to two minutes before it automatically turns off. I read above that...
View ArticleJohn Meacham on DEV-11780 - Teensy 3.0
Yup, it uses gcc and you can program it in plain C or C++. You just need to install the arm-gcc binaries, it is easiest to just download the teensiduino then use the binaries directly out of it even if...
View ArticleCustomer #423373 on KIT-09286 - tinyCylon Kit
omg. lol I love it! But no really…how do I build a giant, walking, talking robot that will not hesitate to do my every command? I WANT THAT! LOL
View Articleraster on DEV-11780 - Teensy 3.0
Love the Teensy! It’s an awesome board. I’ve used dozens of them in projects. :)
View Article